PowerSDR KE9NS v2.8

I found this:
if I disable the function in setup-Cat control- RX A, TX B, Ominirig takes a single virtual Cat in common and everything works regularly without assigning different virtual CATs

I don't use FT8 activity
what I have tested that you can only have one program with Omnirig executable, other running software that have Omnirig mode are disabled

would there be some way to use multiple available Ominirig distinct and separate? I explain I have the station log that uses Ominirig with powersdr, then cw skimmer with Ominirig all assigned with different port with VSP Manager but when they are both open one of the two does not work or works incor...

thanks Darrin Low-High Scan was what I meant. I would lower the scan speed to 5 msec and also Step in Khz in 500 hz or less, or I would set options to the user's liking for speed and step. If I may, I would implement this function in the foreground of the screen in the RX1-VFO A area where you selec...

where can i find the band scan function? where can the user set a start and end of a certain frequency, with the loop function?

Darrin
with the modification to powersdr with cwskimmer transits on the splits pileups very fast. Thank you

But it would be easier if CW skimmer modified their code allow for SPLIT mode operation.

you need to contact VE3NEA. I sent suggestions a few times but he never responded

tnx anyway

p.s. so the Powersdr cat RX2-VFOB port is only for 5000A?

hallelujah, now it works except for the cwskimmer decode window which when you click on the corresponding 599 the window goes up but this is not very annoying.
just explain to us what is the cat RX2 VFOB port for?

I don't understand where I'm wrong. the cwskimmer pile up reads it out of range.
I ran 0.311 repair twice

I think the problem persists. cwskimmer decodes out-of-range calls
in the first photo the signal on red is LZ3ZZ and cwskimmer reports it at around 7013.80

Let's see if I understand. I disable the first field where it says Skimmer com12.
- Field RX2 VFOB (None) Enalbe on.
- RX-A TX-B field insert Com12, Enable on.
Right?

thanks Darrin.
this way it will be easier to catch the correspondent on the pileup

FP/F4HEX tx 14.003. split till 14.006. Cw skimmer reads pileup from 007 outside of pileup range

Is there anyone who can do this test just in case there is some good split pileup? when I use cw skimmer for correspondent hunting in split 599, I set the cw skimmer in the CAT section on powerRX2. everything is ok. the problem is the following: the DX station that operates, as in the case (VK9XU) ...

this was my Tuner in my old Flex 5000 which has always worked without any problems from day one
lou

anyone interested in setting up Power Sdr with the Contest DXlog program to work in RTTY mode.

follow the attached link

https://dxlog.net/sw/#files%2Futilities

strange behavior of CW skimmer with PowerRX2. the anomalous behavior that I encounter for the first time during the split is the following: if you enable PowerRX2 to find the correspondent's 599 it seems that this does not happen. example: if I position myself in split at 14.020 and the DX station t...

Tnx Darrin.
but how can I upload the PDF file to the Forum platform and in which section should I insert it?
if I use Attachements I can't find the PDF file on my PC

versions published on the KE9NS site will not affect after version 2.7.2 it is clearly written

if you want to use that DOC file for POWER SDR community on your web page you decide. Obviously I take responsibility for what I wrote