After updating to 2.8.0.280, I now get no waterfall image (see attached). Worked previously.
any ideas?
...joe kd2qbk
No waterfall after update to 2.8.0.280
No waterfall after update to 2.8.0.280
- Attachments
-
- no waterfall showing
- Capture.PNG (65.56 KiB) Viewed 26400 times
- ke9ns
- Site Admin
- Posts: 524
- Joined: Mon Nov 05, 2018 9:38 am
- Location: Illinois, North West Suburbs
- Contact:
Re: No waterfall after update to 2.8.0.280
I have had that happen to me in the past on my old laptop, but never on my Desktop.
Its not PowerSDR itself causing the issue.
Usually it clears itself after cycling power to both the PC and the Radio.
You can also check for IRQ conflicts (for a 3000 or 5000) per my webpage.
You can do a setup->factory default (it saves you current database to your desktop first)
After that, if it still does not clear up, you can try a windows "System Restore" to a time just prior to the last MS update.
Its not PowerSDR itself causing the issue.
Usually it clears itself after cycling power to both the PC and the Radio.
You can also check for IRQ conflicts (for a 3000 or 5000) per my webpage.
You can do a setup->factory default (it saves you current database to your desktop first)
After that, if it still does not clear up, you can try a windows "System Restore" to a time just prior to the last MS update.
Creator of PowerSDR KE9NS v2.8, based on the Flex Radio PowerSDR v2.7.2 software.
Flex-5000, LDMOS and Titan Amps, G5RV, and Mosley TA-33 Junior
Flex-5000, LDMOS and Titan Amps, G5RV, and Mosley TA-33 Junior
Re: No waterfall after update to 2.8.0.280
Unfortunately, nothing presented worked. Still no waterfall...
- ke9ns
- Site Admin
- Posts: 524
- Joined: Mon Nov 05, 2018 9:38 am
- Location: Illinois, North West Suburbs
- Contact:
Re: No waterfall after update to 2.8.0.280
Then follow the instructions found just below the GREEN incremental download button on my webpage.
That is uninstall, then manually wipe out all the folders.
Then install the the Full and incremental over again.
Darrin
That is uninstall, then manually wipe out all the folders.
Then install the the Full and incremental over again.
Darrin
Creator of PowerSDR KE9NS v2.8, based on the Flex Radio PowerSDR v2.7.2 software.
Flex-5000, LDMOS and Titan Amps, G5RV, and Mosley TA-33 Junior
Flex-5000, LDMOS and Titan Amps, G5RV, and Mosley TA-33 Junior
Re: No waterfall after update to 2.8.0.280
Did the above instructions from Darrin solve the problem?
I'm experiencing the same problem with no waterfall where everything was working previously.
Al
I'm experiencing the same problem with no waterfall where everything was working previously.
Al
- ke9ns
- Site Admin
- Posts: 524
- Joined: Mon Nov 05, 2018 9:38 am
- Location: Illinois, North West Suburbs
- Contact:
Re: No waterfall after update to 2.8.0.280
Usually if everything else is fine, but no waterfall, then shut down, reboot your PC and cycle power to your radio.
That will usually reset the waterfall.
If you find that the CPU% or Temp value is messed up, there is a different procedure.
Darrin
That will usually reset the waterfall.
If you find that the CPU% or Temp value is messed up, there is a different procedure.
Darrin
Creator of PowerSDR KE9NS v2.8, based on the Flex Radio PowerSDR v2.7.2 software.
Flex-5000, LDMOS and Titan Amps, G5RV, and Mosley TA-33 Junior
Flex-5000, LDMOS and Titan Amps, G5RV, and Mosley TA-33 Junior